If you work in industrial maintenance, mining, agriculture, or any field that relies on machinery running 24/7, you’ve probably dealt with grease lubrication pumps at some point. Let me guess—you either love ’em because they keep your gears, bearings, and chains from seizing up, or you’ve pulled your hair out because one’s acting weird (like it’s pumping air instead of thick, sticky grease). That’s where bleeding a grease pump comes in. I’m Jake, part of the grease lubrication pump supply team we’ve built up over the last 10 years, and in all that time, the #1 question we get from mechanics and plant managers alike isn’t “How do I pick the right pump?” It’s “Why won’t my pump prime, and how do I fix it?” Grease Lubrication Pump

Let’s cut to the chase. A grease pump isn’t magic—it just pushes grease through lines to where it’s needed. But if air gets trapped in the lines (or even inside the pump itself), it acts like a tiny air bubble block that stops the pump from building enough pressure. That’s what bleeding a grease pump is: just getting rid of all that pocketed air so your pump can do its job properly. It’s a simple task, but if you skip a step or rush it, you’re gonna end up with lousy lubrication, and worse—unplanned downtime that costs you thousands. I’ve seen a production line shut down for 8 hours because a mechanic skipped bleeding the pump and a bearing burned out. Don’t be that person.
First, let’s talk about when you actually need to bleed a pump. Not every time your pump sputters, by the way. Here’s the short list: if you’ve just installed a new pump (or replaced an old one), if you refilled the grease reservoir (that’s the big tank at the top or side of the pump, right when I say reservoir), if you noticed grease leaking from line joints, or if the pump pressure gauge is reading way lower than normal (or no reading at all). Those are the big red flags. Bleeding for no reason? Not needed. You’re just wasting time and grease.
Now, let’s get into the actual steps. I’m gonna walk you through this like I’m showing you over the shop floor, no fancy tech jargon, just what works. First, gather your tools. You don’t need a huge toolbox—just a few basics: a small container (like an old 1-quart plastic jug) to catch any leaked grease, a 5/16-inch wrench (most grease pump bleed fittings use this, but double-check yours—no shame in measuring), a rag (grease is messy, trust me), and of course, the right grease for your pump. Wait, important side note: never mix grease types. If your pump is labeled for NLGI 2 grease, don’t use NLGI 0 just because it’s easier to pump. That’ll mess up your system and make bleeding way harder.
First step: Prep. Turn off the machine the pump is connected to, and lock it out/tag it out (LOTO). This isn’t just safety rules—it’s common sense. If the machine turns on while you’re working on the pump, you’re gonna get hurt, and the pump is gonna get banged up. Next, check the grease reservoir level. If it’s low, fill it up to the “full” mark—but leave about an inch of space at the top. Why? Because when you start pumping, grease expands a little, and if the reservoir is packed to the brim, there’s nowhere for the air to go. Air needs room, so don’t overfill. Also, give the reservoir a quick wipe down. No dust, no dirt—dirt in the reservoir is the #1 reason you need to bleed a pump in the first place, because it can clog lines or fittings.
Second step: Prime the pump manually. Most grease pumps have a manual handle or a prime button, right? Locate that. Don’t hook the pump up to the machine yet if it’s a new install. Just push or pull that manual handle (depending on your pump model) slowly. Go too fast, and you’ll just churn more air into the grease. Do this 5 to 10 times. What you’re looking for here is grease starting to come out of the bleed fitting (I’ll get to that next). If after 10 pumps you’re still only getting air, that might mean the inlet filter is clogged. Pop that filter out, clean it with solvent, and put it back in—clogged filters are a super common culprit for trapped air. We get at least 2 calls a week from guys who skipped checking the filter and thought their pump was broken, when all it needed was a rinse.
Third step: Locate the bleed fitting. This is a tiny, threaded valve (usually with a square or hex head for a wrench) that’s somewhere on the pump, or sometimes on the main grease line right after the pump. If you can’t find it, pull up your pump’s manual. Wait—hold on—we always tell our customers to save the manual that comes with their pump, not throw it away. I’ve heard way too many people say they lost theirs and spent an hour hunting for the bleed fitting. If you didn’t get a manual, most of the big pump models have the bleed fitting within 6 inches of the grease outlet. It’s not hidden, it’s just easy to miss if you’re rushing.
Fourth step: Open the bleed fitting. Grab that 5/16-inch wrench, put it on the bleed fitting, and turn it counterclockwise about a half-turn. Don’t unscrew it all the way—just enough to let air escape. If you take it all the way out, grease will go everywhere, and you’ll be picking it off the floor for days. Now, this is where patience comes in. Start pumping the pump (using the manual handle) slowly. You’ll first see a mix of air bubbles and grease come out into your catch container. Keep pumping. The air bubbles will stop, and you’ll see a steady, solid stream of grease with no bubbles. When that happens, it’s time to close the fitting. Turn it clockwise just until it’s snug—don’t crank it so hard you strip the threads. Stripped threads on a bleed fitting are a headache, I promise.
Fifth step: Bleed the line outlets. Wait, you’re not done yet. The bleed fitting on the pump gets most of the air, but there might still be some in the individual lines that go to each bearing or fitting. How do you do that? Locate the first grease line outlet on the pump. Some pumps have multiple outlets, each for a different line. If that’s the case, work on one at a time. Take the small line fitting where it connects to the pump outlet, loosen it about a quarter-turn. Now, pump the manual handle slowly, and watch the loose line fitting. You’ll see air sputter out, then grease. When grease comes out steadily, snug the line fitting back up. Do this for every outlet on the pump.
Pro tip here: If you’re bleeding a pump that’s connected to multiple distant lines, start with the line closest to the pump first, then work your way out to the farthest one. That way, you push air forward through each line one by one, instead of pushing it back into the pump. I learned this the hard way on a job at a grain mill a few years back. The mechanic tried bleeding all lines at once, and air got trapped in the longest line, so we had to redo it. Took us 2 extra hours, and we lost half a bucket of grease. Don’t make that mistake.
Another pro tip: If you’re still getting air after doing all this, there’s a good chance the line itself has a leak. Check every line joint, every hose clamp, every threaded connection. Even a tiny pinhole leak will suck air in when the pump is running, which means you’ll be bleeding it every week. If you find a leak, tighten the fitting or replace the hose. We always tell our customers to use heavy-duty grease lines, not cheap vinyl ones—they crack easier, cause leaks, and make bleeding a nightmare.
Wait, what about electric grease pumps? Most of the steps I just went through work for electric ones too, but instead of pumping a manual handle, you run the pump for 10 to 15 seconds at a time. Don’t run it nonstop for 5 minutes—you’ll overheat the motor and burn it out. Stop every few seconds to let air escape through the bleed fitting. Also, on electric pumps, make sure the pressure relief valve isn’t stuck open. If the relief valve is open, you’ll never build enough pressure to push air out. Give the relief valve a quick tap with a wrench if it’s sticking—usually that works.
Let’s talk about common mistakes that make bleeding way harder than it needs to be. First, rushing. I’ve seen mechanics bleed a pump in 2 minutes, then come back an hour later because it’s still sputtering. Slow down. Take your time, pump gently, wait for the air to stop. Second, using the wrong grease. Like I said earlier, mixing grease types is a big no-no. Different greases have different consistencies, and they don’t mix well, so they’ll trap air. Third, overfilling the reservoir. I can’t stress that enough—leave that inch of space. If you fill it to the top, when you start pumping, grease will push against the trapped air and force it into the lines, instead of letting it escape through the bleed fitting. Fourth, ignoring the inlet filter. That little mesh filter on the bottom of the pump inlet is there to keep dirt out, but when it’s clogged, it restricts grease flow, so air can’t escape. Clean it every time you refill the reservoir, or at least every 3 months.
Now, how often should you bleed your grease pump? Most of the time, you only need to do it when you install it, refill the reservoir, or replace a line. But if you work in a super dusty environment (like a mine or a construction site), you might need to check for trapped air every month. We’ve seen a pump in a rock quarry that needed bleeding every 2 weeks because dust got into the reservoir and clogged the filter, so air kept getting trapped. If you notice uneven grease distribution (like some bearings are dry, and some are over-greased), that’s a sign you need to check for air, which means bleeding.
Let’s wrap this up. Bleeding a grease pump isn’t rocket science, but it’s one of those maintenance tasks that saves you so much hassle down the line. I’ve talked to plant managers who’ve cut their unplanned downtime by 30% just by making sure their pumps are properly bled. It takes 15 minutes, uses a little grease, and prevents bearing failures that cost thousands to fix.
If you’re struggling with a pump that won’t prime, or you need to replace a worn-out pump that’s been giving you grief, we’ve got you covered. Our team has been supplying grease lubrication pumps for over a decade, and we work with everyone from small farm shops to big industrial plants. We don’t just sell pumps—we help you figure out which one fits your needs, and we’re here to answer any questions you have about bleeding, maintaining, or repairing your system.

If you’re ready to upgrade your current grease pump, or you need advice on keeping your existing one running smooth, hit us up to connect with our team for a consultation. We’ll hook you up with all the info you need, no sales pressure, just honest advice from people who work with these pumps every day.
Resistive Systems References:
- Machinery Lubrication Magazine. "Priming and Bleeding Grease Lubrication Systems", 2021.
- National Lubricating Grease Institute (NLGI). "Best Practices for Grease Pump Maintenance", 2022.
- Industrial Maintenance and Plant Operations. "Troubleshooting Grease Pump Air Entrapment", 2023.
Sunshine Machinery Co., Ltd.
As one of the most professional grease lubrication pump manufacturers and suppliers in China, our products have good reputation in the market. Please rest assured to buy durable grease lubrication pump made in China here from our factory. For price consultation, contact us.
Address: No.852, Qingfeng South Road (South), Tongxiang City, Zhejiang Province
E-mail: export@ishan.com.cn
WebSite: https://www.ishanlube.com/